Series |
Model |
Description |
|
FK-F |
|
The FK-F Series displacement/vibration transducer is an eddy-current transducer
designed to satisfy the American Petroleum Institute API
St'd 670. It measures the shaft vibration of rotating
machinery without contact. |
|
FK-F |
|
The FK-F Series displacement/vibration transducer is an eddy-current transducer
designed to satisfy the American Petroleum Institute API
St'd 670. It measures the shaft vibration of rotating
machinery without contact. |
|
VK-A |
|
The VK-A Series
vibration transducer is an eddy-current transducer designed
to satisfy the American Petroleum Institute API St'd 670.
It measures the shaft vibration of rotating machinery
without contact. |
|
VK-A |
|
The VK-A
Series vibration transducer is an eddy-current transducer
designed to satisfy the American Petroleum Institute API
St'd 670. It measures the shaft vibration of rotating
machinery without contact. |
|
VK-P |
|
The VK-P Series TSI transducer is a high-grade
eddy-current type non-contacting transducer for shaft
position and differential expansion measurement of rotating
machinery required for TSI. |
|
VK-P |
|
The VK-P Series TSI transducer
is a high-grade eddy-current type non-contacting transducer
for shaft position and differential expansion measurement
of rotating machinery required for TSI. |
|
VK-P |
|
The VK-P Series TSI transducer is a high-grade
eddy-current type non-contacting transducer for shaft
position and differential expansion measurement of rotating
machinery required for TSI. |
|
VK-P |
|
The VK-P Series TSI transducer
is a high-grade eddy-current type non-contacting transducer
for shaft position and differential expansion measurement
of rotating machinery required for TSI. |
|
CV |
|
The CV-85 velocity transducer measures
the casing vibration of rotating machinery such as turbines,
compressors and pumps, and outputs a voltage signal proportional
to velocity vibration. Generally, as this is a self-generating
moving coil or electrodynam (to be
discontinued). |
|
CV |
|
The CV-86 piezoelectric
velocity transducer measures the casing vibration of rotating
machinery and outputs a voltage signal. It has a built-in
piezoelectric acceleration detection element and converts
the input signal to a voltage signal. |
|
CV |
|
The CV-87 high-temperature velocity transducer
can be continuously used at temperatures up to 375°C
and therefore is most suitable for measuring the bearing
vibration of gas turbines. |
|
CA |
|
The CA-301 acceleration
transducer is an on-line facility diagnostic vibration
sensor used for motors, pumps and fans in petrochemical
plants and steel and iron works. The CA-301 is a unique
low-cost vibration sensor for PM (Predictive Maintenance). |
|
CA |
|
The CA-72 Series Acceleration Transducer
is a piezoelectric type acceleration vibration transducer.
Generally, the vibration of rotating machinery supported
by anti-friction bearings may include high frequencies.
|
|
RD |
|
The RD Series tacho driver
is an eddy-current non-contact revolution detection transducer.
It is usually difficult to measure accurately the speed
of rotating machinery in the low rotating region, but
this transducer can measure any speed from zero upward. |
|
MS |
|
MS Series Magnetic Pickup mounted near
the observed gear outputs a frequency signal (detected
frequency) proportional to the rotating speed of rotating
machinery. It is most suitable for controlling the number
of revolutions. |
| VK Series |
|
The VK-R Series transducer is an eddy-current
transducer designed to satisfy the American Petroleum
Institute API St'd 670. It measures the shaft vibration
of rotating machinery without contact. This transducer
has a feature of long cable extension. |
| PK Series |
|
The PK-452P transducer measures the gap
between the piston set as the target and located in any
reciprocating compressor and the sensing surface of this
transducer, there by allowing the amount of rider ring
abrasion to be measured. |
|
|
Multipurpose accelerometer,
100mV/g top connector |
RN Series |
|
Multi-purpose accelerometer, 100mV/g, side
connector |
| RN Series |
|
Low frequency accelerometer,
500 mV/g top connector |
RN Series |
|
Low frequency accelerometer, 500 mV/g side
connector |
| RN Series |
|
High temperature accelerometer,
100 mV/g top connector |
RN Series |
|
High temperature accelerometer, 100mV/g
side connector |
| RN Series |
|
Piezo velocity transducer,
100 mV/g, top connector |
RN Series |
|
Piezo velocity transducer, 100 mV, side
connector |
| RN Series |
|
Piezo velocity transducer,
100mV/g integral cable |
RN Series |
|
Piezo velocity transducer, 100mV/g side
exit integral cable |
| RN Series |
|
Triaxial accelerometer, 100
mV/g, side connector |
RN Series |
|
Magnetic mount accelerometer, 100 mV/g,
side connector |
| RN Series |
RN-AC117-1A |
Accelerometer, 50 mV/g, top
connector |
RN Series |
|
Accelerometer, 50 mV/g, side connector |
| RN Series |
|
Multi purpose accelerometer,
100 mV/g top exit integral cable |
RN Series |
|
Multi purpose accelerometer, 100 mV/g side
exit integral cable |
| RN Series |
|
Low cost accelerometer, 100mV/g
top connection |
RN Series |
|
Loop Power, velocity
4-20 mA output, top connector 10-1000 HZ |
| RN Series |
|
Loop Power, velocity 4-20
mA output top connector 3-2500 Hz |
RN Series |
|
Loop Power, velocity 4-20 mA output top
exit integral cable |
| RN Series |
|
Loop Power, velocity 4-20
mA output, side exit integral cable |
RN Series |
|
Loop Power, acceleration 4-20 mA output,
top connector |
| RN Series |
|
Loop Power, acceleration 4-20
mA output, side connector |
RN Series |
|
Loop Power, acceleration 4-20 mA output,
top exit integral cable |
| RN Series |
|
Loop Power, acceleration 4-20
mA output, side exit integral cable |
RN Series |
|
Dual output sensor, temperature/acceleration,
top connector |
RN Series |
|
Dual output sensor, temperature/acceleration |
